Proprietà:Caption en
Jump to navigation
Jump to search
Property to mantain the caption of an image, assigned to paramenter "Note_it" on some template (currently only on ToolPhotoInfo).
8
Tool to disassemble the piston mechanism of a [[Aurora 88 Big]]. +
A
Tool to simplify the opening of an overlayed cap. Upper view. +
Tool to simplify the opening of an overlayed cap. Side view. +
An ''[[Arkansas Stone]]'' usable for nib smoothing. +
Equipment for galvanizing gilding: solution for gilding and 5V transformer obtained from a mobile phone recharger, with the addition of crocodile clips. Note the cotton pad used to distribute the gilding liquid on the positive crocodile. +
Two wrenches for the disassembly of the internal nut for the fixing of the clip and the inner-hood inside an [[Aurora 88]] cap for the two known variants: with two notches at 180° and three notches at 120°. Note that in the case of the wrench for the three-notch variant one tooth (shown by the arrow) is longer. +
Detail of a metal tube used for feeder extraction from an [[Aurora 88]] section. It can be made from an aluminium cilinder of the proper size. +
B
Scales with centigram accuracy. +
A ''[[Vacumatic block]]'' to dismount a [[Vacumatic]] mechanism. Has two different threads sizes, standard and big. It can be used also to dismount some [[piston filler]] mechanisms (the ones protected by a [[blind cap]]) having care to verify that threads are matching. +
Two-speed hot air generator, detail of the outlet nozzle. +
C
A self-produced wrench to open and tighten the ring nut that locks the piston seals of an [[Aurora 88]]. +
A self-produced wrench to open and tighten the ring nut that locks the piston seals of an [[Aurora 88]]. +
Shaft with support for cork for seal reconstruction, for [[Lucens]] cork seals. +
A set of tools used to make cork seals. +
D
Tool to keep the rubber sacs open during replacement in order to facilitate the engagement on the attachment of the section: example of the use with a rubber sac. Found in an original [[Eversharp]] repair toolbox from 30s / 40s. +
Tool to keep the rubber sacs open during replacement in order to facilitate the engagement on the attachment of the section. Found in an original [[Eversharp]] repair toolbox from 30s / 40s. +
E
An inner cap extractor, open, in the position that is used when put inside the inner cap. +
An inner cap extractor, closed, in the position used when it has to be inserted inside the inner cap. +
An ''extraction block'' (or ''punch block'' or ''knockout block'') with some aluminium cilinders of various diameters used to estract the feeder pushing it from the back of the section once it has been dismantled. In the center note the hollow cylinder to extract the feeders that have protruding elements in the center (for example breather tubes). +
F
Brass corkscrew for grommets, gaskets and corks. +
Surgical scissors pliers, very useful for hooking internal parts (such as I or J bars) to pull them away or insert them into the barrel. +
Two alcohol stoves of different sizes, as alternative, for those who have acquired sufficient practice, to [[:File:Phon-Aria-Calda.jpg|hot air guns]]. They allows a good precision on the area to be heated, but are very risky to use with celluloid pens that could ignite. +
I
Self-built tool for inserting the sac in a [[Waterman]] [[Waterman 5116|5116]]. +
L
Polishing brush for finishing, made of fabric threads, and ingot of less abrasive paste for final polishing. +
Roughing polishing brush, made with strips of fabric, and stronger abrasive ingot for polishing. +
Example of a drill anchored on a vice and equipped with a [[polishing brush]]. +
M
A small light hammer, suitable for operations with the [[extraction block]] or for other operations where some delicacy is required. +
Reverse screw taps used to remove screws locked in the seats. +
Three sizes of ''Micromesh'' abrasive papers in sizes (from right to left): 12000, 8000, 6000. +
Tool for measuring the pitch of a screw, allows you to determine it directly from the threads so you can repeat them in the same way. +
N
A '' [[nib block]]'' and a ''[[burnisher]]'' for repairing nibs. +
A '' [[nib block]]'' for repairing nibs. +
A '' [[nib block]]'' for repairing nibs. Made in RAKU, produced by some people from [https://www.acps.it ACPS] and the [http://forum.fountainpen.it fountainpen.it forum]. +
A '' [[nib block]]'' for repairing nibs. Made in RAKU, produced by some people from [https://www.acps.it ACPS] and the [http://forum.fountainpen.it fountainpen.it forum]. +
A '' [[nib block]]'' for repairing nibs. Made in RAKU, produced by some people from [https://www.acps.it ACPS] and the [http://forum.fountainpen.it fountainpen.it forum]. +
A '' [[nib block]]'' for repairing nibs. Made in RAKU, produced by some people from [https://www.acps.it ACPS] and the [http://forum.fountainpen.it fountainpen.it forum]. +
A '' [[nib block]]'' for repairing nibs. Made in RAKU, produced by some people from [https://www.acps.it ACPS] and the [http://forum.fountainpen.it fountainpen.it forum]. +
A '' [[nib block]]'' for repairing nibs. Made in RAKU, produced by some people from [https://www.acps.it ACPS] and the [http://forum.fountainpen.it fountainpen.it forum]. +
Two thin plastic sheets with a single abrasive side of grit grains (9000 and 2400) to be used inside the nib [[slit]]. +
O
Magnifying glasses, generally used in electronics, with visor support and the possibility of using interchangeable lenses, used to be able to closely observe the parts of a pen while working, keeping your hands free. +
Countersinking lens, with front opening and measuring grid to the tenth of a millimeter. +
P
Wooden puller used in the repairs of [[Vacumatic]] to push the diaphragm mechanism from below (from the side where the section is screwed after having it unscrewed) without damaging the shaft of the diaphragm. Necessary when the diaphragm is petrified or stuck to avoid stress applied to the mechanism, it should be used in the flared part (better visible in [[:Image:Parker-Vacumatic-PusherEstrattore.jpg|this other image]]). +
Precision cutters for removing the ''pellet'' of a [[Vacumatic]] diaphragm, diameters 0.8 and 1.6 mm. +
A nut with a longitudinal cut used to dismount a [[Vacumatic]] mechanism. +
A nut with a longitudinal cut used to dismount a [[Vacumatic]] mechanism. +
An aluminum ''[[pellet pusher]]'' and a wooden extractor used in the repairs of [[Vacumatic]]. In particular, note the countersunk head in the extractor in order to correctly apply the pressure to the loading mechanism by wrapping the pellet seat. +
Conical plug used for removing the filling mechanismo of a [[Vacumatic]], alternative to using a wooden puller such as [[:File:Parker-Vacumatic-Estrattore.jpg|this]]. +
A piston filler extractor for the [[Pelikan 400]] and similar ones, must be used after removing the nib assembly from the section to push back the mechanism (it is a pressure joint). +
Aluminium cylinder with staggered section, called ''[[pellet pusher]]'', on which the [[diaframma Vacumatic|diaphragm]] of a [[Vacumatic]] to be replaced must be inserted. It is used to insert the glass ball into its housing and reverse the diaphragm more comfortably when it is repositioned on the mechanism. +